This Dual Interceptor Gauge is designed to work with a number of Chrysler, Dodge and Jeep vehicles including:

• 07-12 Dodge Caliber
• 08-09 Dodge Caliber SRT-4
• 06-10 Chrysler PT Cruiser

This is the DUAL setup of Aeroforce Interceptor Scangauges famous gauge. This Dual gauge setup will allow you to monitor 4 lines of parameters whereas the single gauge setup will show 2 lines of parameters.

We are proud to introduce the Aeroforce Interceptor gauge. This gauge installs easily and quickly by plugging into your OBD2 port under your steering wheel. This means you can install this gauge with NO special tools, no cutting, no soldering, and in most cases have it wired up and running within 25 minutes!

• RPM
• MPH
• Intake Air Temperature (post Intercooler)
• Engine Coolant Temperature
• Battery Voltage
• Long Term Fuel Trim
• Short Term Fuel Trim
• O2 Sensor Voltage
• Manifold Pressure (vacuum/boost) displayed in PSI
• Ignition Advance
• Knock Retard
• Fuel Status (open/closed loop)
• Throttle Position Percentage
• Engine Load
• Ability to check AND ERASE ENGINE CODES
• Ability to record engine parameters for 60 seconds and review parameters.

Gauges are available with Black and White faces and Silver and Black Bezels. The Displays lettering will show in RED.

Furthermore, you can piece together custom faces for your gauge set with a red "SRT" logo! Add the faces in the color you want and the SRT overlay to create a matching look for your interior! Be sure to purchase two of each for dual gauge sets.

The Interceptor gauge is 52mm (2 1/16") in diameter and will fit in all standard gauge pods of this size. A 5' cable is included with appropriate OBD2 connector.

A function menu is available by pushing both buttons simultaneously. One menu option allows you to enter a record mode. Once selected, the Interceptor will return to normal scan mode, but will start recording the displayed data automatically when the throttle exceeds 60%. Approximately 60 seconds of data will be stored. Returning to the menu screen, you can choose to replay the stored data on the Interceptor display.

The gauge displays 2 parameters at a time, but can be programmed to cycle through up to 8 parameters during a user determined period of time. This way you can monitor several items without taking any other actions.

High intensity LEDs can be used as shift lights or warning lights to indicate when a selected parameter exceeds an entered threshold. Due to the gauges extremely fast update rate, this light is very accurate and easy to set. Once you try it you'll find you can't live without it!

Another menu option offers the ability to swap the foreground and background colors of the display. Using this feature, for example, the gauge with a black background and blue characters (negative image) becomes a blue background with black characters (positive image). Not only can this be visually appealing but beneficial in changing lighting conditions. Positive images are easier to read in bright sunlight, negative at night.

The Interceptor's scan rate can also be adjusted through a menu function.

DTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options.This essential feature will help the gauge to pay for itself the first time the check engine light comes on. Those that have modified their vehicle will find this very handy when a sensor, vacuum line, etc. has been inadvertently left disconnected, or something was just not put back together properly.

The two analog inputs can be configured through menu choices. A linear conversion can be entered so that an analog signal connected to the gauge can be read in appropriate units. These inputs are handy for pressure signals such as those from MAP and oil pressure sensors, analog outputs from Air/Fuel ratio kits, etc. These signal can then be read and recorded along side the other parameters obtained on the vehicle's bus.

The gauge has bi-directional controls allowing for manual control of the low and high speed fans.

Last but not least, the Interceptor will measure 0-60 times, as well as 1/8 and 1/4 mile time and speeds. This is accomplished through a simple menu selection.

Installation is accomplished by simply plugging the supplied connector into the OBD2 port below the steering wheel. Literally plug-and-play!

Here are some photos of the Interceptor in use on a 08 Caliber SRT4.

Top shows Instant Miles Per Gallon (MPG)
bottom shows Throttle percentage.

Top shows Short Term Fuel Trim, Bottom shows RPM

Top shows Coolant, Bottom shows Catalytic Temperature

Light output for this Aeroforce Interceptor Scangauge is Green.

Please note: Aeroforce is no longer shipping these guages with the metal U shaped bracket for mounting. They claim that they found almost all customers are using pods that dont require the metal U shaped bracket, and so they are no longer shipping these gauges with that bracket and nuts. If you are mounting this gauge into a pod, we would recommend using electrical tape around the body of the gauge for additional friction to hold it more tightly into the pod upon insertion.